Home About Us News Products Part and Service Contact Us
Products > Wheel Loader > LIUGONG WHEEL LOADER
LIUGONG CLG856II Wheel Loader
    Introduce:


     

                                                              CLG856 LIUGONG Wheel Loader
    Main Technical Specificaions
    Parameters for Entire Loader
    1
    Bucjet capacity
    3m³
    2
    Rated Load
    5000kg
    3
    Lifting Time of Acting Arm (Full Load)
    <6.5s
    4
    Sum of Three Items
    <11.5s
    5
    Maximum Loader Speed of Each Gear
     
     Forward Gear ?
    37km/h
     
     Forward Gear ?
    23km/h
     
     Forward Gear ?
    11.5km/h
     
     Forward Gear ?
    6.5km/h
     
     Backward Gear ?
    6.5km/h
     
     Backward Gear ?
    11.5km/h
     
     Backward Gear ?
    23km/h
    6
    Traction
    160 5kN
    7
    Max. Breakout Force(Rotating Bucket)
    160 5kN
    8
    Max.Climbing Gradient
    30'
    9
    Min.Turning Radius:
     
     Wheel Center
    5795 50mm
     
     Outer Side of Bucket
    6775 50mm
    10
    Geometrical Dimensions:
     
    Length of Loader(wih bucket placed on ground flatwise)
    8060 100mm
     
    Width of Loader(Outer side of wheel)
    2750 50mm
     
    Width of Bucket
    2976 30mm
     
    Height of Loader(Top of cab)
    3467 50mm
     
    Wheelbase
    3250 30mm
     
    Wheel Tread
    2150 10mm
     
    Mix.Clearance from Ground(float area of front and rear loader frame)
    431 20mm
     
    Max.Hoisting Height
    3100 50mm
     
    Offloading Distance at Max Hoisting Height
    1035 50mm
    11
    Weight of Loader(with cab included)
    16800 200kg
    12
    Driver Seat: Located over the float of loader frame)
    Engine
     
    Diesel Engine
    Cummins 6CT8.3-C215 Model Diesel Engine
     
    Rated Rotate Speed
    2200r/min
     
    Max.Torque
    872N.m/1500r/min
     
    Fuel Consumption Rate under Calibrated Operating Condition(Dais Experiment)
    233g/kw.g
     
    Fuel
    0#Light Diesel Oil
     
    fan Diameter(Air Exhaust)
    762mm
    1
    Hydraulic torque Converter
     
    Model
    Single Stage Three Units
     
    Conefficient of Torque Conversion
    2.55
     
    Cooling Mode
    Wind Cooling Pressure Cycle Type
    2
    Transmission Case
     
    Type
    Fixed Spindle Dynamic Gear Shift
     
    Gear Position for Shift
    Four-Gear Forward&Three-Gear Backward
     
    Working Pressure of Shift Oil Pump(Gear Pump)
    1.6~1.8Mpa
    3
    Main Transmission and Deceleration beside Wheel
     
    Type of Main Transmission
    Spiral Bevel Gear Stage 1 Deceleration
     
    Type of Wheel Deceleration
     
    Deceleration Ratio
    23.5
    4
    Driving Axle and Loader Wheel
     
    Type
    Four-Wheel Drive
     
    Tire
    23.5-25
     
    Air Pressure of Tire
    0.32 0.01Mpa
    Braking System
    1
    Service Brake
     
    Type
    Full Hydraulic Wet Type Brake
     
    Brake Oil Pressure
    6Mpa
     
    Cut-in Pressure of Charge Valve
    12.3Mpa
     
    Cut-out Pressure of Charge Valve
    15Mpa
     
    Low Pressure Alarm Pressure of Service Brake
    10Mpa
     
    Nitrogen Pre-pressure in Accumulator
    5.5 0.05Mpa
    2
    Parking Brake and Emergency Brake
     
    Type
    Automatic and Manual Motor-driven Type
     
    System Oil Pressure
    13.8Mpa
     
    Low Pressure Alarm Pressure of Service Brake
    10Mpa
     
    Cut off Pressure of Emergency Brake
    5.5Mpa
     
    Nitrogen Pre-pressure in Accumulator
    5 0.05Mpa
    Steering Hydraulic System
     
    Type
    Float Loader Frame, Full-Hydraulic Flow Amplified Steering System
     
    Steering Cylinder Number-Bore X Stroke
    2-?90*485mm
     
    Steering Pump
    CBGj2063/CBGj101 Model Gear Pump
     
    System Working Pressure
    16Mpa
     
    Flow
    138.6/35.2L/2200r/min
     
    Turning Angle
    38' 1'for Left and Right, Respectively
    Working Device
     
    Oil Cylinder Number of Acting Arm-Bore X Stroke
    2-?160*794mm
     
    Rotating Bucket Oil Cylinder Number-Bore X Stroke
    1-?180*540mm
     
    Distributing Valve
    Pilot Duplex Valve Rod Type
     
    Model of Working Pressure
    P7600-F140L Model Gear Pump
     
    Flow
    308L/2200r/min
     
    System Working Pressure
    20Mpa
     
    Pilot Working Pressure
    3.5Mpa
     
    Working Device
    Single-Rocker Recersal 4-Connecting Mechanism
    Electrical System
     
    System Volage
    24V
     
    Battery
    2-BA31750T
     
    Lamp Voltage
    24V
     
    Diesel Engine Starting
    Starting with 24V Voltage
    Filling Capacity
     
    Fuel
    280L
     
    Hydraulic Oil
    210L
     
    Crankcase
    22L (with scale of oil level rule as actual filling Volume)
     
    Transmission Case System
    45L (with scale of oil level rule as actual filling Volume)  
     
    Front Axle(Main Transmission and Wheel Reducer)-36L(with scale of oil level rule as actual filling Volume)
     
    Back Axle(Main Transmission and Wheel Reducer)-6L(with scale of oil level rule as actual filling Volume)
    Air-Conditioning System
    1
    Heating
     
     
    Work Medium
    Cooling Water of Diesel Engine
     
    Heating Capacity
    5000kcal
    2
    Cooling
     
     
    Work Medium
    Freon F12(R12)
     
    Cooling Capacity
    4000kcal
    3
    System Voltage
    24V